Dyna-Cure Applicator Instructions

The SHR-1 Forage Sprayer System is a basic tank mix unit with tank, pump, and flow controls for easy application of forage treatment products.

SPECIFICATIONS:

 

TANK: 25, 50 or 75-gallon capacity – ULV stabilized.

  • 25, 50 or 75-gallon crosslink polyethylene tank, acid resistant, ULV stabilized (resists deterioration in sunlight).

  • Bottom drain. Can be cross connected to dual tank for extra gallons and longer running time.

  • Top vented with 100 mesh screen to eliminate contamination by drawing dust from crop into tank as tank pressure equalizes in tank.

  • Raised fill spout to prevent dust from entering tank when refilling.

  • Molded with built-in sump so maximum amount of liquid is usable.

  • Equipped with return from regulator valve for mixing while running.

  • Fittings spin welded into tank and threaded with standard pipe threads.

  • Mounted in steel frame for easy mounting on all types of equipment.

  • Strainer 40 mesh nylon screen with 18 square inches of surface area to prevent plugging.

  • 100 mesh strainer in line w/valve – easy to clean.

 

PUMP: 12-volt, heavy duty – permanent magnet

  • Heavy duty 12 VDC PM electric motor (7 amp max current draw).

  • Pump body fiberglass filled to withstand high pump pressures without distortion.

  • BUNA-N Diaphragms for maximum flexibility in a cool weather operation.

  • Built-in pressure switch for a maximum 60 psi, for pump protection.

  • All pump fittings are compression sealed type with 3/8” barb.

  • Motor base shock mounted on rubber to eliminate vibration.

 

PIPING and FITTINGS: Non Corrosive

  • All plumbing made from polypropylene, nylon, PVC or stainless steel.

  • Pressure regulator valve with locking nut can be set from 10 to 60 psi, to set flow rates to match application requirements.

  • Anti-siphon valve to prevent loss of liquid when system is not in use.

  • In-line pressure gauge.

  • 20’, 3/8” ID Tubing, ULV stabilized polypropylene to withstand sunlight.

  • All barbed fittings polypropylene (standard pipe threads).

 

NOZZLE SYSTEM: Easy Service

  • Nozzle body shipped with winged nozzle nut, for easy service of nozzle and screen. (No wrench needed)

  • Stainless Steel Nozzle. (Shipped with 2, .50 flood jet standard)

  • Other sizes available for higher flow rates on request.

  • Nozzle body mountings bar (can be forced to direct spray where needed)

 

CAB MOUNTED SWITCH PANEL

  • Heavy duty switch.

  • Green indicator light showing when unit is on.

  • 10 amp fuse and holder.

  • 24’ of automotive service wire.

 

FLOW METER

  • All plastic body for anti-corrosion.

  • Easy to disassemble to clean.

 

ACCESSORY PACKAGE (optional)

  • Micro switch

  • Variable speed switch

 

STEP 1 – MOUNTING THE TANK

On side or underneath swather: The mounting braces are furnished (at extra cost). Mount solid enough to support the weight of full applicator. When full of water, the sprayer will weigh 280 to 900 pounds. Make the mounting brackets fit the holes in the bottom pan frame of the unit.

STEP 2 – ATTACHMENT OF SPRAY HOSE, FLOW METER AND FILTER ASSEMBLY

Attach spray hose onto the fitting under the tank at the pressure relief valve. Run the hose to flow meter (mounted where visible). Then to filter assembly, use clamps to secure the hose to the fittings.

Run the hose over to the equipment feed intake. Secure with quick ties out of the way of moving parts.

STEP 3 – SPRAY HEAD BRACKET

Mount spray head to allow a spray width of 4-5 feet. Spray pattern should be wide enough for spray to cover the width of the feed, for good coverage from side-to-side. Mount behind the gathering auger and in front of the conditioner. Mount for even spray distribution. Mount on deflector shield if possible.

STEP 4 – SPRAY HEAD

Place nozzle body through the spray bar and secure with the body nut tightened against the spray head. Adjust the bar angle for good spray patterns. Attach the hose to the spray head.

STEP 5 – WIRING THE UNIT

Attach black wire (neg.) to neg. wire on accessory plug. Attach the red wire (pos.) to the 12-volt accessory plug (positive wire), with good connectors (center post is positive). Turn the unit switch “ON” and “OFF” to make sure you have good connections.

STEP 6 – CHECK OUT THE SYSTEM

Put 5 gallons of clean water in the tank. Turn on the unit. Flush out the system by removing the nozzle and screen. Replace the nozzle and screen – adjust the flow rate to 10-12 ounces per minute. Use a measuring cup with an ounce scale on its’ side. Time the flow for 60 seconds. Adjust the flow rate by turning the flow adjustment handle and retighten the nut to secure the correct flow rate.

STEP 7 – ADJUST THE NOZZLE BAR

Adjust the nozzle bar for best position for maximum coverage of feed intake or chopper or swather.

STEP 8 – FILL AND MIX

Fill the tank up to the desired level for spray application according to the application rate directions. Use the formulas provided by inoculant manufacturers.

Calf silhouette blue.jpg
Corn Seed Silhouette.jpg
Alfalfa Silhouette.jpg
Potato Plant Silhouette.jpg
  • Facebook Clean
  • LinkedIn Clean
  • Twitter Social Icon
  • Instagram Social Icon

KeyAg Distributors, 4525E, 3425N, Murtaugh, ID 83344          800-388-3659           Text/After Hours: 208-432-2318          Disclaimer/Privacy Policy  © 2016-2019 Pacer Technology